When building a GPU based mining rig you’re obviously going to need a bunch of GPUs. These GPUs will be connected to a single motherboard. That immediately becomes a problem unless you have a specialized mining motherboard. Most motherboards only have one or two PCIe X16 slots for installing video cards.

This is where splitters and PCIe riser cards become useful. However, most boards only have four to six PCIe slots available.

Well it turns out there’s another solution: 4 in 1 PCIe risers.

4 in 1 PCIE Risers Explained

4 in 1 PCIe risers are a fantastic way to get some additional PCIe slots in your motherboard.  Much like standard PCIe risers, they allow the connection of X16 PCIe GPUs to plug into an X1 PCIe slot. Additionally, they allow for the card to “rise above” the motherboard making room for the cards in the first place.

It would be next to impossible to place six GPUs on a single motherboard due to spacing even if the GPUs were X1 capable. It should be noted there are some special mining motherboards designed to support 6 or more GPUs directly on the board. However, these are generally far more expensive than just buying a standard motherboard and set of riser cards.

Check out a selection of mining motherboards on Amazon.

Asrock H110 Pro BTC+ 13GPU Mining Motherboard Cryptocurrency

After checking the price on Amazon above, now you might see why a splitter is a viable option for mining builds.

With 4 in 1 PCIe risers, you can now take this concept to the next level by plugging up to four PCIe riser cards into a single PCIe X1 slot. There are some caveats you should be aware of though. You can only use as many of these as your motherboard has PCIe lanes. If your board has four slots, but only six lanes you would run out of PCIe lanes before you ran out of slots.

The good news is that most motherboards have about twenty PCIe lanes. Some of the slots on your motherboard are likely X4, X8, and of course X16.  Since all of them are being used as X1 slots, you’re probably OK.  The only way to know for sure is to check your part number on the manufacturer’s website.

Are PCIE Splitters compatible across vendors?

One question I get asked a lot about PCIe risers cards in general, but especially about these 4 in 1 PCIe risers is “Are they compatible with each other even if they are different brands?”  The answer is: Probably. Unfortunately there is no easy way to tell.

The good news is that I’ve found very few that are not. Most all of them use the same chipsets and firmware. The only way to know for sure is to try it. I would generally say out the eight different brands I am using, I have found only two that are not compatible with each other.  They tend to either just work, or not work at all. So that at least makes it easy to troubleshoot.

4 in 1 PCIE Risers – Recommendations

I’ve personally tested these riser boards.  My favourite by far are the BNing 4 in 1 PCIe splitter. They are constructed very well and have a great reliability record in my GPU mining rigs. Besides that, there is a bad ass knight rider LED effect happening on the side of the card that just screams cool!

BGNing PCI-E 1 to 4 PCI express 16X slots Riser Card PCI-E 1X to External 4 PCI-e Slot Adapter PCIe Multiplier Card for Bitcoin Miner
WBTUO Riser Card PCIe 1 to 4 PCI Express 16X Slots Riser Card PCI-E 1X to External 4 PCI-e Slot Adapter PCIe Port Multiplier Card

This site contains affiliate links to products. We may receive a commission for purchases made through these links. 

PERFORMANCE WITH 4 IN 1 PCIE RISERS

After installing 4 in 1 PCIe risers you should look closely at your performance specs. I’ve seen situations where these risers simply do not perform in certain slots. Again, check with your motherboard vendor to make sure the slots are supported slots. In these cases I have found that the single riser will work fine. Just move the 4 in 1 to a different PCIe slot. Lower than expected hashrates will be the most common indication there is a comparability problem with the slot.